01Hidden Mechanics

How Does a Ball Bearing Reduce Friction?

A ball bearing swaps sliding for rolling, cutting friction to a fraction of a plain bearing’s. Here is how its rings, balls, cage and oil film work together.

Rows of polished silver-coloured metal spheres arranged on a dark surface

Almost anything that spins smoothly, from a bicycle wheel to an electric motor or a desk fan, relies on bearings. Spin a good bicycle wheel by hand and it keeps turning for a surprisingly long time. Without bearings, the axle would rub directly against its housing, wasting energy as heat and wearing both parts away.

The ball bearing is one of the most common solutions, and its trick sounds simple: replace sliding with rolling. But why is rolling so much easier than sliding, and why does a ball bearing still need lubrication if its balls simply roll? The answers involve the elastic squashing of steel, microscopic films of oil and some careful engineering of each part.

The short answer

  • A ball bearing places hardened steel balls between two rings, so the moving parts roll over each other instead of sliding.
  • Rolling friction for the same materials is typically 100 to 1,000 times smaller than sliding friction, because it comes mainly from slight elastic deformation rather than surfaces scraping past each other.
  • Manufacturers quote friction coefficients of roughly 0.001 to 0.005 for rolling bearings, compared with about 0.01 to 0.02 for typical plain bearings.
  • A very thin film of lubricant, usually less than a thousandth of a millimetre thick, keeps the metal surfaces apart and prevents wear.

The basic principle: rolling instead of sliding

When two surfaces slide over each other, the tiny high points on each surface catch and grind against one another. The force needed to keep them moving is described by the familiar friction equation:

F = μ × W

where F is the friction force, W is the load pressing the surfaces together and μ is the coefficient of friction. Reducing μ is the whole game.

Rolling changes the situation fundamentally. A rolling ball does not drag its surface across the track; each point on the ball touches down and lifts off again. People have exploited this for thousands of years. The move from dragging loads on sledges to carrying them on wheels is a classic example. A ball bearing applies the same idea inside a compact, precise component.

How it works, step by step

A typical rolling bearing has four basic parts:

  1. Inner ring. This is usually fitted onto the shaft and turns with it. Its outer surface has a smooth groove, the raceway, for the balls to run in.
  2. Outer ring. This is usually fixed in the housing. Its inner surface carries a matching raceway.
  3. Rolling elements. In a ball bearing these are balls; other bearing types use cylinders, tapered rollers or needles. They carry the load while rolling between the two raceways.
  4. Cage. Also called a retainer, it keeps the balls evenly spaced and stops them from falling out. It does not carry the main load.

When the shaft turns, the inner ring rotates, the balls roll around the raceways and the outer ring stays still. The load passes from shaft to housing through the balls, but the only motion at each contact point is, almost entirely, rolling.

The science behind it

Where rolling friction comes from

If steel balls and rings were perfectly rigid, rolling would waste almost no energy. Real steel is slightly elastic. Under load, the ball flattens a tiny amount and the raceway dents slightly where they touch. At the leading edge of the contact, material is being compressed, which resists the motion. At the trailing edge, the material springs back, but not perfectly: a little energy is lost inside the steel, much as a dropped ball never quite bounces back to its starting height. This loss through repeated deformation is known as elastic hysteresis, and it is the main reason rolling is not completely frictionless.

The other contributions

Bearing manufacturers model total friction as the sum of several parts. SKF’s published friction model, for example, separates them into:

  • Rolling friction, from elastic hysteresis and from the work of drawing lubricant into each contact and pushing the excess out.
  • Sliding friction, because even nominally pure rolling contacts involve small amounts of slip caused by surface deformation and the curved shape of the contact.
  • Seal friction, from rubber seal lips rubbing on the rings. For bearings with contact seals this can be a large share of the total.
  • Drag losses, from the balls and cage churning through oil in oil-bath lubrication.

Typical friction coefficients

Because these losses are small, bearing friction coefficients are tiny. The table below shows reference values published by the bearing maker JTEKT (Koyo) for stable operation under normal conditions.

Bearing type Typical friction coefficient μ
Deep groove ball bearing 0.0010–0.0015
Angular contact ball bearing 0.0012–0.0020
Self-aligning ball bearing 0.0008–0.0012
Cylindrical roller bearing 0.0008–0.0012
Tapered roller bearing 0.0017–0.0025
Plain (sliding) bearing, for comparison 0.01–0.02, and in some cases 0.1–0.2

The bearing maker NTN describes rolling bearing friction as generally less than one hundredth that of a sliding bearing. Actual values depend on bearing type, load, speed and lubrication.

A worked example

A common engineering estimate of a bearing’s friction torque is:

M = F × μ × d ÷ 2

where M is the friction torque, F is the load, μ is the friction coefficient and d is the bore diameter. As an approximate illustration, take a deep groove ball bearing with a 25 mm bore carrying a radial load of 1,000 N, with μ = 0.0015:

M ≈ 1,000 × 0.0015 × 12.5 mm ≈ 19 N·mm (about 0.019 N·m)

At 1,500 revolutions per minute (about 157 radians per second), the power lost is roughly 0.019 × 157 ≈ 3 W. Applying the same simple formula with a plain-bearing coefficient of 0.01 to 0.02 gives roughly 125 to 250 N·mm, or about 20 to 40 W lost as heat. These figures are rough estimates for comparison only; the values above apply to unsealed bearings with good lubrication, seals add friction, and real plain bearings are designed and calculated differently.

Why lubrication still matters

Rolling bearings, as a rule, need lubricant. Inside each loaded contact, the pressure is high enough to deform the steel elastically and to make the oil far more viscous than it is in the open. The result is an elastohydrodynamic film: a layer of oil, usually less than one micrometre thick, that is nonetheless thick enough to separate the microscopic peaks on the smooth bearing surfaces. If that film fails to form, for example because the lubricant runs short, the metal surfaces touch, leading to surface damage, wear and in severe cases seizure.

Real-world applications

Ball bearings are found wherever a shaft needs to turn freely under load: wheel hubs, electric motors, fans, pumps, gearboxes, power tools and many household appliances. Their low starting friction is particularly useful. A plain bearing has relatively high friction when it first starts to move, whereas a rolling bearing’s starting torque is very small, which makes rolling bearings well suited to machines that start and stop frequently.

Different designs suit different loads. Deep groove ball bearings handle general radial loads; angular contact bearings handle combined radial and axial loads; and roller bearings, with line rather than point contact, carry heavier loads. Bearings are also made in special materials, including stainless steel and ceramic rolling elements, for demanding environments. Our article on why stainless steel does not rust easily explains what makes such steels resistant to corrosion.

Common misconceptions

“Ball bearings have no friction”

Their friction is very low, but not zero. Elastic hysteresis, small amounts of slip, lubricant shearing, seals and oil drag all consume some energy, which is why bearings warm up in use.

“If the balls only roll, they don’t need lubricating”

The lubricant does not just reduce sliding. It forms the thin film that keeps the surfaces apart under very high contact pressure, protects against wear and helps prevent corrosion. A dry bearing will quickly wear or fail.

“The cage holds the balls up”

The cage keeps the balls evenly spaced, but the load is carried by the balls pressing between the two raceways. The cage itself is a source of a little sliding friction where the balls rub against it.

“More grease or tighter seals are always better”

Seals keep dirt out and lubricant in, but contact seals add noticeable friction, and excess lubricant can add drag. Bearing makers specify amounts and seal types for each application.

Limitations and exceptions

  • Fatigue life. Even a perfectly lubricated bearing eventually fails. Repeated stress between balls and raceways causes surface flaking. Engineers use the basic rating life, L10 = (C/P)³ for ball bearings, to estimate the number of revolutions that 90% of a group of identical bearings will reach, where C is the bearing’s dynamic load rating and P is the equivalent load. Doubling the load cuts this estimated life to about one eighth.
  • Start-up friction. Friction when a bearing first starts turning can be up to about twice the running value.
  • Temperature. NTN notes that bearings of standard high-carbon chromium steel with ordinary heat treatment can show significant dimensional change if used above 120 °C for long periods, so special heat treatment is used for hot applications.
  • Plain bearings can compete. A well-designed plain bearing running on a thick, full film of oil can have friction similar to a rolling bearing, and is often preferred where shock loads, quiet running or very compact size matter.
  • Safety. Worn bearings in vehicles, lifting equipment or powered machinery can fail suddenly. Inspection and replacement of such bearings should be carried out by a qualified technician, with machinery isolated from its power source.

Frequently asked questions

Why are bearing balls made of hardened steel?

The contact area between ball and raceway is tiny, so the local stress is very high. Hard, fatigue-resistant steel keeps deformation elastic and resists flaking over millions of revolutions.

How much friction does a ball bearing remove?

Published coefficients for rolling bearings are around 0.001 to 0.005, roughly one hundredth of a typical plain bearing’s, although the real saving depends on load, speed, lubrication and seals.

Why does a bearing get noisy or rough?

Common causes include worn or flaked raceways, contamination by dirt, and loss of lubricant. Any of these allows metal-to-metal contact or uneven rolling.

What is the difference between a ball bearing and a roller bearing?

Balls touch the raceways at a point, giving very low friction; rollers touch along a line, which spreads the load over a longer contact. Friction depends on the design: in JTEKT’s reference values, cylindrical roller bearings are as low as or lower than deep groove ball bearings, while tapered roller bearings are somewhat higher.

References

  1. NTN. Rolling Bearings Handbook (Cat. No. 9012/E).
  2. JTEKT Corporation (Koyo). Frictional coefficient (reference) – Basic Bearing Knowledge.
  3. SKF Evolution. Using a friction model as an engineering tool.
  4. Encyclopaedia Britannica. Rolling friction.
  5. R.S. Dwyer-Joyce, T. Reddyhoff and B.W. Drinkwater. Operating Limits for Acoustic Measurement of Rolling Bearing Oil Film Thickness. Tribology Transactions, 2004.
  6. Roymech. Bearing Friction.

Header photo: Henrique Ferreira on Unsplash.

David

Editor, The Hidden Layer

David edits The Hidden Layer. He writes and updates the site's explanations of everyday science and engineering, checks each article against its cited sources, and handles corrections.